Dress with thin straps (pattern - diagram). Dress with straps Dress pattern with straps

Model 1.

If you are going to create something using any methodology, read it, understand the details, so that you get an idea of the process. Take this manual, for example. See what point K means? This is the depth of the notch at the center of the front. Points 3 and 6; this is the depth of the armhole cutout. Compare these values with what you want to have as a result of the simulation. You can change them to either side, i.e. decrease or increase. The same can be said about the width of the entire product at the chest and waist. This is just an example that shows you one of the trends in modeling this kind of blouses or dresses.

If you have not yet built a base pattern for yourself, use our step-by-step instructions and do it.
We take a drawing of our base pattern and copy the shelf and back onto a blank sheet of paper

See Fig. one

To build, we need a separate back and shelf.

Rice. 2

On the pattern-base of the back, along the side cut down from point P, measure 4 cm and set point 1. From point 1, draw a horizontal line to the intersection with the middle line of the back and set point 2. This will be the upper cut of the back.

Fig. 3

Stepping back from side cut base patterns 1 cm to the left, draw a new side cut line parallel to it.

Fig4

We close the dart. We draw the upper and lower cuts with a smooth line.

Fig5

On the pattern of the base of the front, close the bust dart, transfer it to the dart at the waist. To do this, we cut the line G74 (points G7 and 4 denote the tops of the darts of the chest and from the waist).

Fig6

The top of the new dart (point E) will now be on the bisector of the angle of the open dart at a distance of approximately 4 cm from point G7. To build, you can use a compass.

Fig. 7

Along the line of the side cut down from point P, measure 4 cm and set point 5. Having departed from the side cut by 1 cm, draw a new line parallel to the previous line of the side cut. From point 5, draw a perpendicular to the intersection with the new side cut line and set point 6.
Now we draw the upper cut of the front of the bodice. On the line of the middle of the front downward from point B4, we set aside 13-15 cm we get point K. From point G7 up along the line of the closed tuck we set aside 10 cm we get point K1. Connecting points K, K1 and point 6, we draw up the line of the upper cut of the front.

Rice. eight

Figure 9 shows the details of the cut of the back and front of the bodice. We will adjust the length of the straps in the process of trying on the figure.

And as always, I wish you creative inspiration and confidence in your abilities!

Download in one file | Turbobit | | |

The rights to this article belong exclusively to the author. Full or partial use of the materials of this article in electronic editions of the Internet is possible only if the following conditions are met:
Information about the author should be retained. In the title or at the end of the published reprint, the source www.site of the Internet resource "Sewing Master" with a direct, active, visible by the user, not closed from indexing by search engines, a hyperlink to this article should be indicated.
The republishing of texts by newspaper, magazine editions or other replication outside the Internet is possible only with the written consent of the author.

Style Description:

This dress with thin straps is one-piece. The silhouette is straight, free, darts are only on the chest, there are no darts at the waist. Almost all fabrics can serve as material for manufacturing, both lightweight, cotton fabrics, linen, silk, and dense, woolen fabrics. The standard dress length is mid-knee length or three fingers above the knee. But it is quite possible to sew such a dress of any length and decorate it as you wish. When making such a dress from thick or textured fabrics, the width of the harness can be slightly increased.

Technical drawing

How to model this style:

To make this dress on thin straps, you need a scale ruler. How to make it and how to use it, see the article"Sewing scale".When cutting fabrics it is necessary to make allowances for seams and hem. Each piece on the fabric should be placed along a shared thread, otherwise there may be distortions in the product. Pattern - the diagram is given based on a standard figure of size 48, It is easier and more convenient to use graph paper to make patterns.

Front building:

Draw a right angle with apex at point A

Draw a vertical line 84 cm

Draw a horizontal line 26 cm.

From T. A put down 23 cm.

Set aside 10 cm horizontally from T.A. (the place where the strap is sewn)

Set aside 26 cm horizontally from 23cm.

Set aside 18 cm from the point 84 cm.

From point 84 cm, set aside 36 cm.

Set aside 2 cm from point 36 upwards.

For darts along the side line, lay 4 cm from top to bottom (first dart). The length of the darts is 8 cm, the depth is 2 cm. The distance between the darts is 3 cm.

Back construction:

1. Draw a right angle at point A

2. Lay down 80 cm downward

3. Lay aside 24 cm horizontally.

4. From T.A. set aside vertically 19 cm.

5. From point A, set aside horizontally 10 cm (the place where the strap is sewn)

6. From point 19 draw an auxiliary line 24 cm

7. From point 80 to set aside 17 cm

8. Defer 34 cm from point 80.

9. From t 34 set aside 2 cm upwards.

Connect the resulting points in accordance with the drawing

Shoulder strap: strap length 42 cm, width 5 cm (ready-made 2.5 cm).

Material consumption:

one length plus 20 centimeters. This style can be attributed to economical models.

this style is suitable for almost all women, regardless of their shape. However, curvy women should avoid fine, shiny fabrics and stretch jersey when sewing this style. For overweight women in this case, more dense materials are suitable. The waistline can be emphasized with a thin leather strap, which can be bright or contrasting with the main color of the dress. Recommended dress length: to the knee or slightly above the knee, but other lengths are possible.

What material is preferable for sewing:

The model can be made from any kind of material. It can be made either from fabric with a pattern or plain.

Sewing difficulty level:

production does not require much effort, entry level, suitable for beginners.

Modeling options:

This style can be used as a basis to which, if desired, original additional decorative elements can be added as a result, resulting in a modified style. Ruches, flounces, folds, additional straps can act as such decorative elements.

What clothes can be combined with:

A dress with thin straps made of lightweight fabric can be worn solo or combined with a light blouse or T-shirt with short sleeve... Such a dress made of dense fabric can be combined with a regular blouse, shirt. The dress with thin straps will perfectly fit into the wardrobe of almost any style. You can add completely different accessories and decorative elements to it. Made from "dressy" material, it can be a sophisticated option evening dress... This style looks stylish in a duet with a short fitted jacket, with a long fitted jacket or knitted openwork cardigan.

All ingenious is simple! This motto proves once again our beige dress with spaghetti straps. Making a pattern for this dress is very simple, as you will see when you start building a dress pattern.

So what's the secret behind this adorable spaghetti strap dress? It's all about the fabric! An openwork beige fabric with pronounced stripes of patterns is the soloist in this model.

IMPORTANT! The lace that you will use to sew a dress with straps must be elastic, since there are no darts on the dress.

Spaghetti Straps Dress: Pattern

The pattern is given for size 46-48.

Before you start building a dress pattern on spaghetti straps, you need to take measurements:

Chest circumference - 92 cm
waist circumference - 70 cm
Hip girth - 96 cm
Dress length from the waist - about 56 cm

Rice. 1. Dress pattern on spaghetti straps

Spaghetti Straps Dress: Modeling

Build a pattern for the front and back of the dress with spaghetti straps as shown in the pattern for the dress.

If your measurements differ from those given above, calculate the required values using the formulas given.

IMPORTANT! The dress with straps is sewn only from elastic materials. The front and back of the dress on the straps are cut one pattern at a time.

How to cut a spaghetti strap dress

Dress with spaghetti straps is sewn with a cover.

Cut out from elastic lace: front and back of the dress, one pattern at a time, with allowances for seams along the side seams - 1cm. Do not make allowances on the bottom of the dress, but arrange the pattern so that scallops go along the bottom of the dress. ...

Cut to match from elastic lining fabric: front and back of the dress, one pattern at a time, with allowances for seams along the side seams - 1 cm. Do not make allowances for the front cutout and armholes (!)... Allowances at the bottom of the dress made of lining fabric - 3 cm.

For straps and dressing the neckline and armholes of the dress, you will need a braid about 1cm wide with scallops on both sides and length to measure (about 80cm for the straps and about 120cm for the neckline and armholes).

The dress with straps is sewn on an overlock with an elastic seam.

How to sew a spaghetti strap dress

Sweep and grind the side seams of the dress with straps. Process the allowances.

Sweep and grind the details of the dress from the lining fabric, process the allowances, tuck and stitch along the bottom.

Fold the cover with the dress on the wrong sides, sweep along the cut of the front, back and armholes, and then continue to process the dress as a single layer.

Process the allowances of the armholes and necklines of the front and back of the dress with an overlapping seam. Sew tape along the neckline and armholes of the dress.

Measure the required length of the strap tape. Apply and topstitch, tucking the ends of the tape.

You can download 3 patterns for sheath dresses of different models. One pattern is built with long sleeves, two on spaghetti straps. The dresses have a lot of darts, which will allow you to simply "fit" them on almost any figure.

I don't like the very name "case". It blows from him, as well as from “ hourglass", Marketing of the lowest kind, clinging to human sexuality. Instead of "case", you can simply say - a fitted dress that is not cut off at the waist. It's not like a "collar", "cascade" or "year", where there is a clear visual similarity or the name of the cut detail, there is a direct allusion to 90-60-90 ... Case ... I just remember Chekhov.

Well, let it be a sheath dress. We will not disassemble dresses with spaghetti straps. You can read the instructions for them at the pattern. long dress... Minor differences in length and workmanship will not be an obstacle.

Dress cutting case, lining, additional details

For the model, you can select the fabrics from which the sheath dress is usually sewn.

For the lining of the dress, use the back, front and flank without seating areas for the neckline and cut allowances, shortening by 2 cm.

Add 1.5 cm on your own to the middle seam of the back, 1 cm to the rest of the seams, 3 cm to the hem of the sleeve bottom, 4 cm to the hem of the bottom of the dress, 2 cm to the hem of the bottom of the lining.

Before sewing the neckline of the dress, duplicate it with adhesive interlining. To cut the gasket, use a facing pattern without allowances.

Instructions for sewing a dress with sleeves

Cut off the slit allowances from the right barrel and the right relief of the front of the dress, leaving a 1 cm allowance for the seam.

Transfer the lines of the darts from the patterns to the dress. Sweep, grind and iron the darts at the waist of the front and back of the dress, iron the allowances to the middle, iron the chest darts of the front down.

Sew the middle seam of the back of the dress from the bottom to the place where the zipper is sewn in, the patterns are built without a zipper mark, buy it 55 cm long, sweep the seam allowances and iron them out. Sew a zipper into the middle seam of the back.

Transfer control marks to the reliefs. Sew embossed seams of the front and back of the dress, aligning the control marks, neaten and iron to the middle.

Sew shoulder seams of the dress.

Transfer control marks from the pattern to the sleeve and armholes. Sew the cuts and bottom of the sleeve of the dress. Connect on sewing machine and press the seam on the sleeve. Sew the sleeve into the armhole of the dress, aligning the marks on the pattern, press it on.

Fold back the hem of the bottom of the front and the allowance of the cut on the wrong side, stitch the corner of the joint diagonally, cut off the excess fabric to 1 cm, turn it out and iron it, in the same way grind the corner of the joint on the left barrel of the front. Iron the hem of the bottom of the dress and the allowances of the cut on the wrong side, overcast and hem with blind stitches, also hem the bottom of the sleeves.

Connect the lining details in the same way as the dress and hem the hem.

Sew the lining to the lower edge of the neckline facing and press the seam onto the lining. Fold the lining, combined with the facing of the neckline, with the front sides inward, overstitch the neckline, notch allowances, press on the facing and topstitch. Insert the lining into the dress, tuck the cuts of the lining armholes and sew with blind stitches to the armhole allowances.

On our site you can also download a tight sleeveless.

Final sewing operations

Fold up the open seams of the middle seam of the back lining and the hem of the neckline and sew to the zipper with blind stitches. Notch the lining allowances at the upper end of the cut in the left embossed seam of the front, tuck the cuts and sew with blind stitches to the cuts of the allowance.

Sew on the crochet hook and sew a loop.

Chest girth, cm

Waist girth, cm

Hip girth, cm

Chest girth, cm

Waist girth, cm

To set up printing pattern No. 217 in A4 format, use "Test square No. 2"! The test square is located on the first sheet of the pattern file.

Sundress pattern. Sundress on the straps of a tapered A-shaped silhouette, above the knee length. On the front detail, there are chest darts, a V-neckline. The upper edge of the product is overlaid. There are cuts in the side seams.

Product length in the middle of the back in finished form, see: 38 size: 69.6-72.1, 40 size: 69.6-77.2, 42 size: 69.6-77.2, 44 size: 69, 6-77.2, 46 size: 69.6-77.2, 48 size: 69.6-77.2, 50 size: 69.6-77.2, 52 size: 69.6-77.2, 54 size: 69.6-77.2

General gains, embedded in the pattern: Pg: 2.2 cm, Fri: 32.2 cm, PB: 12.5 cm.

Recommended material for sewing: for sewing this product, we recommend natural thin fabrics with a dense weaving weave without stretching. Such fabrics will keep their shape well, remove moisture in the heat and dry quickly. Cotton or linen is perfect. Fabrics can be plain or printed.

Fabric consumption with a width of 140cm: 38 size: 1.0-1.05 m., 40.42 size: 1.05-1.1 m., 44.46 size: 1.25-1.35 m., 48, 50 size: 1.55-1.7m., 52.54 size: 1.65-1.8m.

Details of the pattern are given with allowances for processing.

Sewing difficulty - "For beginners"

The photo shows a sundress sewn in GRASSER according to pattern No. 217

We want you to enjoy working with Grasser patterns, and to make the sewing process clear, therefore a file with a very detailed description, in which all stages of work on the product are considered, with STEP BY STEP PHOTOS SEWING TECHNOLOGIES!

Also given in the description detailed information on the required consumption of fabric, materials and accessories.

The pattern in your order will be in two print options:

1. For printing on A4. You need to print the pattern on an ordinary printer on A4 sheets, then glue the sheets, cut out the pattern and you can sew!

2. For printing on a large format plotter. The details of the pattern are located on a sheet measuring 60 * 172 cm.

March 15.12.2019 02:43:35

Good afternoon. Please tell me if satin or silk is suitable for this model? Thank you

Administrator: Hello, yes, it will do

Valentine 11/21/2019 4:54:21 PM

Good day. I wanted to download a free pattern, sundress. From the phone.
When you click on the "Download pattern" button, a bunch of pages with different symbols / letters opens. And that is all. How can I get a free pattern by email?

Administrator: Hello, on which device do you download the pattern? On the phone? Perhaps you do not have a program for opening zip files installed.
You need to install the program, or open the pattern on another device where a similar program is installed.

The pattern is downloaded on the site, we do not send patterns by mail. Try downloading on a different device.

89500656117 16.11.2019 17:02:47

Hello, is it possible to sew such a sundress from Angora?

Administrator: Hello, our recommendations are that for the fabric to keep its shape well, without stretching, you can choose the composition at your discretion.

Irina 11/13/2019 00:46:25

Good day! Please tell me, I have Og-84 cm, From - 67 cm, About -90 cm, whether 42 size will suit me or is it better to take 44. Thanks in advance for your reply

Administrator: Hello, yes, your size is 42. The size of the dress pattern should be chosen according to the bust.

Our table helps to determine the size -

Adel Vilenskiy 08/23/2019 17:39:28

Hello! Please tell me, for height 165, parameters 91/73/102 which size is better? Considering that the trapezoid, I tend to 44. But I doubt

Administrator: Hello, the size of the dress pattern should be chosen according to the girth of the chest.
According to your parameters, 46 size is more suitable.

Mila I 07/29/2019 10:18:33 AM

Hello! Sewed this summer dress-sundress. But I just can't add my photo to your site with finished product... How to do it?

22.07.2019 13:57:01

Hello!
If you sew a dress on a lining, do you need to change the pattern? or the lining and the main layer are cut in the same way? lining material silk, main - silk muslin

Administrator: Good day!
The lining can be tailored to match the details of the top.

Elena Muratova 07/17/2019 14:15:19

Good day! I can't decide on the size. My parameters are 90-75-102.

Administrator: Elena, good afternoon!
Size 46 is fine with possible reductions in the chest and increases in the hips. We recommend that you sew a mock-up or cut out parts with additional allowances before sewing a product from the main fabric, so that you can release a couple when trying on.

Marina 07/08/2019 16:00:48

Good morning... Can this pattern be used to sew an underwear dress?

Administrator: Marina, good afternoon!
Yes, of course, why not. It depends on what material and what will be the top dress :)

Lyuba 06/26/2019 13:28:18

Help me decide on the size. OG 102, OT 84, OB 105

Administrator: Hello, size 50 is suitable for you

Zulfiya 06/25/2019 21:23:26

Tell me, for chest size 97, waist 90cm what size to take?

Administrator: Hello, size 48 is suitable for you

Daria Novikova 06/19/2019 20:21:33

Hello, help me determine the size for parameters 87-73-99 to take size 44 or 46? Many thanks.

Administrator:

Daria Novikova 07/03/2019 20:18:35

Svetlana 06/18/2019 09:55:42

Hello! Can you please tell me if you can sew such a lined sundress?

Administrator: Hello, you can. We have a pattern without lining, but you can customize it yourself.

Olga 06/18/2019 09:54:54

Good afternoon.
I really want to sew this model on my 56r. Can you please tell me what increments should be made?

Administrator: You can add 1 cm for each slice side seam(4cm in girth), sew the layout and see the fit. Just in case, leave more allowances if there is not enough volume.
The length of the dart may need to be adjusted.
Or maybe it will be necessary to correct the tuck solution. It all depends on your anatomy, breast fullness. All you need to look at the layout, make changes if necessary and transfer to the pattern.

Svetlana 06/15/2019 18:14:43

Hello! Can you please tell me what size to take for parameters 110-97-116, so that it is free, to hide figure flaws? thanks in advance for your reply.

Administrator: Hello, size 54 is suitable for you.

Hope 12.06.2019 15:24:52

Good afternoon. Can you tell me if you can use an extensible doublerin when sewing this cotton sundress.?

Olga 03.06.2019 18:51:48

Good day!
Can you please tell me if the Niagara blouse is suitable for this sundress?

Administrator: Hello, yes, you can sew from Niagara.

Inna 05/27/2019 17:59:17 PM

Hello. OG 82, OT 62. I downloaded 42 size and it is very big. What's the best size? And is it necessary to glue the proportional lines if the material is silk? Thanks in advance!

Administrator: Hello, this pattern should not be big for you, the increase in the chest is only 2.2 cm. You can, of course, take size 40, then in this case you will not have any freedom in chest girth at all.

Tell me, was the print on the correct scale? Was the test square 10 by 10 cm when printing?

Alisa 05/22/2019 21:12:51

Hello, I want a straight cut sundress and below the knees (up to the mid-calf muscles), would it be appropriate if I choose not my height, but more? or is it better to lengthen it yourself?

Administrator: Hello, it is better to choose your height and add the length of the product.
If you are not your height, the bust darts may not be in place.
Better to lengthen.

Anna 05/17/2019 21:22:42

Hello, is the staple okay?

Administrator: Hello, yes, it will do!

Polyanskikh Natalia 14.05.2019 23:59:10

I liked the pattern.
I sewed myself a sundress for study and work from fabric in a cage to wear with blouses.
I made the bottom straight and without cuts.
I would like a similar pattern for large sizes.
My mother has long dreamed of a sundress to wear with blouses in winter and T-shirts in summer.
Her chest size is 124, waist 117, hips 135.

Administrator: Hello Natalia, thank you very much for your feedback! We are glad that we liked the pattern!
About big size think about it.

16.04.2019 00:41:19

Good day! Can you please tell me how to narrow the sundress and make a straight line out of the trapezoid?

Administrator: Hello, you can adjust the side seams, remove as much as you need at the bottom and bring out new lines of the side seams.

Maria 04/05/2019 21:55:42

Hello. Tell me, according to my measurements, I get 42 size with a growth group of 152-158. But your patterns come from 158 growth. Tell me what size to choose. And will I need to make any adjustments?

Administrator: Hello, the size should be determined by the girth of the chest. If you have a bust of 84, then size 42 will suit you. The height should be 158-164.
You may need to transfer the bust darts, this can be determined by fitting.

Ekaterina Bizyaeva 27.03.2019 00:46:22

Good afternoon. I downloaded a pattern, but I can't print it. Test square # 2 with a real print size comes out 10x10, and the pattern itself then does not fit.

Administrator: Hello, please check the "orientation" setting when printing. In this setting, there should be "self-portrait / album", due to an incorrectly set orientation, the margins of the sheet may move out.

Try a different zoom setting, not " real size", and" custom scale ". Set the desired number of percent in it, with which the test square will be 10 by 10 cm. Usually this is 100%, but the settings of your printer may differ.

With the same settings, with which the test square is printed exactly 10 by 10 cm, with a letter and a number in the upper left corner and with margins on all 4 sides, you need to print the pattern as well. Then the pattern will be of the correct size, with margins and numbering.

If you are printing from a browser, please note that printing from a browser may not be correct. It is best to print the pattern by first downloading it to your device.

detailed instructions for printing patterns is on our website -

Maria 03/20/2019 16:24:03

Hello. What size to take on OG 95? I don’t understand 48 in the table is the Russian size?

Administrator: Hello, yes, we have Russian sizes.
For bust 95, size 48 is suitable

Diana 03/05/2019 00:04:32

Good day!

I sew a sundress according to this pattern. I chose the size in accordance with my measurements (height 156, OG 74, OT 60, OB 86), that is, size 38, height 158-164.
After trying on the model, it turned out that the sundress is very large and weighs on me as well as on the mannequin in the video on sewing this model.
The length was below the knee and I reduced it by 10 cm.
The sundress turned out to be wide, so I stabbed 1.5 cm from the sides. I lowered the armhole by the same amount.
And then the grooves. Since the front part was bulging with a fold, I did the same manipulations as in the video: I made incisions to the center of the chest and spread them apart.
You can see what happened in the attached photos. The bust is only 7mm.
Question: Do I need to leave the groove? Or does it turn out that with my proportions it is not needed at all?

Administrator: Hello, I have consulted with the designer - it is better to leave the breast dart.

Natalia 02/15/2019 02:33:12

Please tell me if the fabric is with a pattern, is it possible not to make cuts on the sides?

Administrator: Hello, yes you can!

Evgeniya Rudenko 02/06/2019 20:03:35

Hello, tell me, what size is suitable for the parameters Og 101 From 74 To 102?

Administrator: Hello, there is no need to write the same question under different models. The size of the product is selected according to your body measurements, and will be the same for different models of shoulder products. Since it is selected by the girth of the chest.
Here, for belt products, it may differ, since it is selected by the girth of the hips.

For shoulder garments (dresses, blouses, coats), your size is 50.
For waistbands (skirts, trousers), your size 48

Evgeniya Rudenko 02/19/2019 10:27:50 AM

Good day! Can duberlin strips be used instead of the glue edge, cut, respectively, along the share and obliquely?

Administrator: Hello, instead of an edge, you can use a doublerin cut along the equity. But you need to pay attention to the thickness of the dublerin - dublerin may be thinner than the finished edge.

The slanting edge has a stitching stitch to support the seam and, of course, the thickness of the doublerin also plays a role. In the case of bevel edging, it is better to use it than doublerin.

Elizaveta 02/05/2019 02:22:03

Please tell me, at 86-60-89, what size is better to take so that it does not sit tight?

Administrator: Hello, size 44 is suitable for you

Elizabeth 02/06/2019 19:09:09

What's the size on the photo?

Administrator: Hello, the model is in size 42 and the model itself is in size 42.

Julia 31.01.2019 03:57:29

Hello! Please tell me at 85-64-87, height 154, is it better to take size 40 or 42?
Thanks in advance:)

Administrator: Hello, size 42 is suitable for you

Ruzana 12/22/2018 21:54:37

good evening... I did not understand a little, please clarify! I take a pattern according to my size, and I also need to make additions to this ??? I am waiting for an answer to the mail! Thanks a lot!

Administrator: Hello, no, the increments are already included in the model, you don't need to add anything.

Katya 11.10.2018 00:10:55

Good evening, please tell me about parameters 99-83-104, height 163 what size to choose?

Administrator: Hello, size 50 is suitable for you, height 158-164

Ekaterina 10/04/2018 01:30:40 AM

Hello. Can you please tell me, I am sewing this suede suede on a knitted basis, rather dense material, is it necessary to glue the upper cuts of the neckline, back and armholes? And also a question, I can not find a description of sewing and fabric consumption. Usually available in printed form.

Administrator: Hello, yes, it's better to glue it.

The file with the description is located along with the pattern files in the zip archive that you download from the site.
Look for a file named: Opisanie_poshiva_sarafan_217_pay.pdf

Tatyana 09/07/2018 02:28:03

Good day! Can you please tell me if this model can be sewn from silk? Thank you

Administrator: Hello, you can!

Julia Lobanova 09/04/2018 20:22:10

Very good patterns. Sewing their cotton 100% topic on this pattern. I am very happy!

Administrator: Hello. Thank you very much!! Wear it with pleasure!

[email protected] 15.08.2018 16:49:18

Hello, usually all your sewing patterns fit perfectly on me. In general, I have a very standard 44 size, even the seamstresses in the atelier praised it. But this sundress somehow ... dangles, or something. It feels like he is too big in the girth area above the chest. That is how it should be?

Administrator: Hello, no, it shouldn't be. Check the bodice of the sundress with the patterns - you haven't stretched the top? The cuts are oblique and can easily deform.

And all the shapes still have features, so sometimes some models need adjustments.

Olga 08/09/2018 16:59:37

Good afternoon. Can you please tell me if leather, suede, artificial leather is suitable for this model? I want to winter version such a sundress. Thank you.

Administrator: Hello, yes, it will do.

Olga 08/16/2018 03:48:17

Elena 07/26/2018 11:49:30

Hello!
Thank you very much for the pattern and master class!
The pattern did not suit me a little, I chose the correct pattern for my height (158-164), but the darts are located as if they were for a higher height. About 2 cm below.

Administrator: Elena, good afternoon!
Thank you for your feedback. We are glad that you appreciated the pattern and the master class!
The location of the darts may depend on individual characteristics figure, as well as the length of the straps. Therefore, we always recommend that you sew the layout before the main sewing in order to take into account all the nuances of the fit of the product specifically on your figure.

Maria 07/23/2018 11:13:10 AM

Good afternoon. Which size is better for OG 92 and OB 104?

Administrator: Maria, good afternoon!
We recommend that you buy a pattern of size 46, but when sewing a model, add allowances for the hips so that, if necessary, release a few centimeters during fitting. It will be easier to adjust the pattern for the thighs than for the chest.

Balnur Kubasheva 07/17/2018 15:56:52

Hello. In the master classes, you used an adhesive edge, but what if I did not find such adhesive edges in my city (with and without a thread in the middle). And you order, delivery is problematic. And I live in Kazakhstan in Aktau. In our stores there is only spider web-braid. Adhesive, dublirins are in meters. How to be something that can be replaced, tell me. Thank you for being there.

Administrator: Good day! You can make a fractional edge yourself by simply cutting the doublerin to the fractional width you need.

Lyudmila 07/12/2018 17:20:26

Hello! Is it possible to cut this sundress obliquely? Less dense fabric?

Administrator: Good day! The pattern is designed for cutting along the equity, if you cut along the oblique, you will have to make adjustments.

Daria Sokova 07/12/2018 17:16:41

Hello! How can I adjust the cut in the cut if I want to remove the width along the entire length of the dress?

evgeniya 07/11/2018 11:43:19

Hello, pdf on the plotter asks for a password when you try to open it in Photoshop / Corel.
I have no task to make corrections, just open and print on the machine.

Administrator: good day! Try to open the pattern in the free PDF software Adobe Reader

Inessa 07/10/2018 16:16:44

Hello, is knitwear suitable for this model?

Malka 07/09/2018 16:42:23

Thank you very much, beloved Grasser, for an excellent pattern as always! Sewn up at times. I wear it with pleasure!

Administrator: Thanks!

Evgeniya 07/09/2018 16:35:31

Hello! I can't download the pattern. Some code is opening ... (

Administrator: Good day! Try downloading the file from another browser on your computer.

Maria Goncharova 07/09/2018 16:18:56

Hello, I printed out a pattern - a test square 10 by 10. But the allowances are strange - there are more side seams than in other places. Maybe something with the settings? And more specifically, on the side-1 cm, on the neck and armholes-0.7 cm .And the edging along the edge of the page is 1.5 cm. Just in the previous pattern there was a smaller

Administrator: Good day! That's right, this model has such machining allowances.

Oksana 07/04/2018 01:49:06 PM

Tell me, please, a teenage girl OG 76, OT 65, and hips 90 ... Height 167. I'm afraid taking size 38 she won't fit in the thighs ...

Administrator: Good day! When choosing the size of the shoulder garments, we recommend focusing on the bust girth and, if necessary, adjusting the pattern in the hip area.
We advise you to choose size 38 and widen the pattern slightly around the thighs.

Ksenia 06/29/2018 20:13:48

Hello, tell me, is the fabric with a coupon suitable? I printed out the pattern and I see that the bottom is not straight.

Administrator: Hello, yes, the bottom is rounded, whether it works or not depends on which coupon.