DIY wire ornaments. Wire weaving: work features and examples of finished jewelry

A fashionable and elegant accessory to any look will be homemade jewelry made of wire and large all kinds of beads. They are easy to create, but at the same time look original and expensive. It is important to think over all the details ahead of time and purchase the necessary materials and tools.

Of course, the most important thing is to purchase wire. The wire is easy to use, but more importantly, it is flexible, discreet and comfortable.

Wire products can be different colors and types, they can suit both women and men.

Tools and materials

In order to independently make a wearable product from wire, you do not have to look for complex devices. In total, everyone may need the usual pliers, a hammer, round nose pliers and a small vise.

Only here it is worth considering that when working with wire it is better to use specialized pliers, they have a smoothed inner surface and they cannot damage the material.

Special devices also include pliers with nylon removable pads, they serve to straighten an unsuccessfully twisted wire spiral.

When choosing a working material, thick electrical wire deserves more attention, which can be purchased at all electrical stores.

If the source material is too rigid and does not bend at all, it must be softened by heating over the stove. When doing this, be sure to work with gloves, otherwise you can easily seriously injure your hands.

In jewelry, wire with a diameter of 1 mm, 0.6 mm and 0.2 mm is most often used.

It is best to use a wire with a diameter of 1 mm, in order to better fill the gap between the beads, if they are used.

Also, the thicker the wire, the longer it will last. And if the wire is thin and the decoration is with beads, then the accessory will not last long, because the wire, when moving freely inside the beads, will rub against their edges and, eventually, having become too thin, it will simply break.

Lighting should be good, do not work in the dark or twilight.

Types of weaving wire accessories

Today in the world there are several basic techniques used in creating their masterpieces by masters and creators around the world.

wire wrap

This technology is considered the most popular in its field. With it, you can gracefully braid beads, stones. Thanks to her, original cafes, earrings, brooches, etc. are obtained.

Viking Knit

This weaving technique is not as beautiful and openwork as the previous one, and outwardly resembles the usual knitting from yarn. It is also called "chain mail".

At the very beginning, when you get acquainted with any kind of creativity, panic and confusion always begin. Where to begin? What if it doesn't work? These are understandable fears, but you should not run away from difficulties and quit without even trying.

From one attempt will not happen the end of the world, but perhaps there will be a new favorite pastime. Just do not immediately take on the most difficult, any science must be comprehended from the bottom.

For example, it would not be bad to try to build a bracelet. For him, you don’t need too much, just scissors, a pen shaft, wire, glue and rhinestones.

First, of course, you need to build a foundation. It requires a wire about 20 cm long, rolled up in a loop to look more like a cross. Next, you need a new piece of wire. They need to wrap the first part with movements in the form of zigzags.

After 2 rows are made using this method, the workpiece itself must be transferred to the back of the handle shaft. From this moment, a new wire is gradually woven in, with which you need to make “loops” as in the very beginning.

At the end, when the bracelet takes the desired length, it will have to be removed from the rod, as well as remove all unnecessary, fasten and decorate with rhinestones.

Precautionary measures

When working with wire, there are some safety rules that must be observed, it is important that the hobby cannot be the cause of a tragedy, even the smallest one.

For safety reasons, it is better to wear gloves before work, and hide your eyes behind glasses. When working with sharp cutting objects, such as round nose pliers or side cutters, you should be careful and attentive, otherwise you may accidentally injure yourself.

Simply put, you should not be careless with wire, it is better to act slowly and carefully, so you will be safe, and the decoration will turn out even more beautiful.

Photo of wire jewelry

Beaded jewelry looks very gentle and feminine on the hair. You can wear them with a festive outfit or wear them every day to add romance and sophistication to your look. Bead jewelry can be quite modest and delicate or truly luxurious - a lot depends on which beads and model you choose. By the way, you can buy beads for decoration on purpose or use one or more of your beads that you no longer intend to wear.

DIY beaded hair jewelry can be made in several ways. To your attention - a selection of master classes of varying complexity.

Method 1: Beads + glue

By “planting” beads, rhinestones, crystals on glue, you can decorate a headband, a large or small hairpin, a “crab”, a scallop, and so on. With strong glue, you can stick the decor directly on the hairpin / headband, or first decorate it / it with fabric, suede, leather.

Pros of the method: manufacturing speed, the ability to use beads without holes, unlimited possibilities for drawing up patterns and patterns.

Note: you need to be careful with glue so as not to stain the base of the decoration with it and maintain a neat look of the work.

Hairpin decorated with crystals: master class

You will need:

Metal hairpin without decor;

A piece of artificial or natural suede or leather;

Strong glue and a stick for its application;

Possibly tweezers.

Work sequence:

1. Glue a strip of suede to the barrette, tucking the ends inward.

2. Glue beads one at a time to the suede on the hairpin (tweezers may be required for small beads). Let the glue dry and you're done.

Photo and source: psimadethis.com

Hair comb decorated with beads and rhinestones: a master class

You will need:

Plastic or metal comb without decor;

Beads and rhinestones for decoration;

A piece of felt;

Strong glue or glue gun;

Scissors;

Threads and needle.

Work sequence:

1. Cut out an oval, rectangle, or other shape from the felt that matches the size of your comb base (or slightly larger).

2. Glue beads and rhinestones one at a time to the felt, creating an abstract composition or an ordered pattern.

3. When the pattern is ready, cut off the excess material around the edges.

4. Sew the decor to the scallop and fix it with glue to be sure. Let the glue dry and you're done.

Method 2: Beads + fishing line or thread

stringing different size beads and beads on a thin fishing line, you can make beautiful compositions for decorating hairpins, combs, headbands and so on.

Pros of the method: great opportunities for drawing up patterns and drawings, the ability to use a variety of braids, metal elements for jewelry, embroidery elements, the ability to apply your skills in beading.

Note: for such jewelry, only beads with holes are suitable.

Scallop decorated with braid and beads: a master class

You will need:

Plastic or metal comb without decor with a narrow base;

Decorative curly braid in the form of a stem with leaves;

Metal leaves for jewelry;

Suitable beads of one or more types;

Thin line and needle.

Work sequence:

1. Sew a piece of decorative braid to the base of the scallop with a fishing line.

2. Add metal leaves and beads on top. Try to fix each element of the decor quite firmly.

3. At the end, fasten the fishing line well from the inside out. Ready!

Photo and source: lovemaegan.com

Hair band with beads: master class

You will need:

Beads under pearls of three types;

Thin line;

Scissors;

Satin ribbon.

Work sequence:

1. Cut the line about 1m long. String 6 beads on the middle of the fishing line, as shown in photo 1. Pass the fishing line twice into one of the small beads.

2. String 2 beads on both ends of the fishing line and secure them by passing the fishing line through a small bead (see photo 2).

3. Continue weaving as shown in photos 3, 4, 5. Having made the decoration of the desired length, firmly fasten the fishing line and cut the ends.

4. Tie to the ends satin ribbon(it is better to process its edges with fire or hot scissors so that they do not crumble).

P.S. By the way, this jewelry can be worn as a choker or bracelet.

Photo and source: lc.pandahall.com

Hair ornament made of strands of beads under pearls: master class

You will need:

Small metal comb;

Invisible;

Beads under pearls of four types;

Threads or fishing line and a thin needle;

Strong glue or glue gun.

Work sequence:

1. Tie the thread to the comb, string several beads of the same type on the thread.

2. Tie another thread to the comb and string other beads on it. Do the same with the third thread and the third type of beads, and with the fourth, respectively.

3. Collect the ends of the three threads and tie them to the "crown" of the invisibility.

4. Glue a few beads on the base of the comb, masking the threads. Ready!

Photo and source: clonesnclowns.wordpress.com

Method 3: Beads + chains

Beaded hair jewelry can be assembled from a variety of jewelry blanks in the same way as it is done in the manufacture of bracelets, necklaces, beads and other jewelry. You can buy chains and other decorative items on purpose, or you can use unnecessary beads and jewelry.

Pros of the method: fast results, great appearance jewelry.

Note: special materials and tools are needed (at least thin-nosed pliers, also, possibly, wire cutters and pliers).

Hair ornament from pendants and chains: a master class

4. Add a pendant to the side chains, placing them in the middle. The decoration is ready.

There are a lot of high-quality ideas and instructions for making your own wire products on the Internet. Anyone can easily get acquainted with them, and then do something with their own hands. For this, you need a little: your desire, a small amount of skill, personal time and a couple of handy tools. If all this is available, then the only thing left is inspiration.

Beginners

What do you need to make a decoration? Usually here they start the most obvious method - stroke. To do this, you need to take brass, aluminum, silver and other metals. A thick wire is needed simply for the base of this product, and then a thin wire can be twisted at the right angle.

Here, various craftsmen often add stones, beads and beads. It turns out then just wonderful simple little rings.

Rings

More complex exercises will go when cutting the wire about 15 centimeters somewhere. We need it in order to then put beads on it and place them right in the center. When working, use any thing that is similar to the diameter of your finger.

An ordinary candle from a hardware store plays a very good role in this role. The wire is wound around the object so that the ends are on both sides. Fasten everything and everywhere very firmly. It is best to scroll around the beads four times. Then everything can be safely cut off.

The ends should be about one and a half centimeters. Then it must be wound onto the ring so that the buttonholes are equal. We do the same on the other side. The finger will never prick in this way.

Then, with the help of pliers, we press the ends tightly to the rim. The pliers are pressed harder and harder so that the fit is as tight as possible.

The instruction on how to make an alternative wire jewelry is identical in terms of the availability of the necessary materials, but their application is different. The wire is wrapped around the candle. A bead is put on one end.

Then the ends are bound together. We weave the free tip into the one with the bead. From the top we go to the base, and we do this trick three times. Decoration completed.

Bracelets

Jewelry making techniques change frequently. Very often for good execution the bracelet needs a lot of wire, as well as tools - pliers and round nose pliers. Do not forget about a variety of beads that will become the brightest elements.

It all starts with a loop at the very base. After one and a half centimeters, another loop is made with the help of round-nose pliers. The ends will then need to be connected and trimmed. Then you connect all the squares together.

The wire product goes straight into the loop. At the longest end, you need to bend and cut off the excess. Small, we just bend. Then we plant a bead and apply another square. A neat clasp is attached at the end. Bingo!

Earrings

A master class on wire jewelry is usually held with the same auxiliary items. Again, the whole work is built from the loop at the base. Under it, you need to fasten the figure eight. We repeat everything over and over again. We cut the wire and twist everything tighter.

After that, work is already being built with beads. The ends are twisted into a small loop, a bead is pulled in this place, Pliers will then help to form a loop on both sides. The ends are twisted back.

For hair

Little girls, and those who are older, love to decorate their hair in every way. Here you will learn how to learn how to properly weave jewelry, such as hairpins and combs.

If you want, you can learn such a simple craft with your own hands. Always initially draw everything on paper so that there are visible landmarks.

It all starts on one turn, and then smoothly flows to the outer circle. As a result, you should get a beautiful circle with a mustache.

It will be necessary to turn about 6 curls between the beads, and up to 10 between the details. Then you will get a nice-looking work. At the edges, use the smallest details more often, and already in the middle, resort to the help of beads.

The same can be safely said about studs. Photos of wire jewelry show us that all kinds of options are not so few. The main thing is to clearly follow all the instructions that you have, but always think so that you can add your own.

Distinctive features always make your item unique and inimitable. Particularly high-quality options are obtained from copper wire. Here, nippers and drills will already be auxiliary.

As a result, you can observe many interesting work from other authors. Everyone has a wild fantasy. Unique miniature works of art are obtained. If you automate this process, then there will be no end to clients. Now it is a very popular thing on the market.

Photo of wire jewelry

for beads

Instruments: cutters, pliers

Assembly:

At work I will use a large number of materials to show the most diverse selection of accessories that can be used in the assembly of this jewelry. It is not necessary to use all of them at once, as I will do. There are some very beautiful decorations where two, three, or even one type of beads are enough, and they will look just as good if you used all the elements that I will use in my master class. Of the tools we need. In the absence of this tool, it can be replaced with scissors.

The first thing we need is to unwind the wire. For the base of the decoration in the hair, we need a piece of wire 20-25 cm long. In order not to constantly twist the ends of the wires together, I recommend doing all the work on one piece of wire. Therefore, to our base, which is 20-25 cm long, we add another 1 meter of wire and cut off this segment from a common coil.

For the top of the hair jewelry I will use 1 twin bead and 1 simple bead. To begin with, we pass the edge of the wire through one hole of the twin bead, and then through a simple bead. And we move them along the segment so that on one side of the strung beads the length of the wire segment is 20-25 cm, and on the other side of the beads the wire segment will be equal to 1 meter.

Next, take the short edge of the wire, remind you that its length is 20-25 centimeters and draw it through the second hole of the twin bead. We tighten. After that, the beads must be twisted on the wire. 10 turns is enough. The beginning of our branch is ready.

We proceed to the next branch, which will consist of 5 small ones. We string them through the long edge of the wire. We advance them to the first branch. Holding the beads with one hand, we begin to bend the wire, forming a circle of beads resembling a flower. Then we twist the wire together until we reach the previous element with the top.

The second element of the branch is ready. To proceed to the next step of making hair ornaments, you need to twist the wires along the main trunk of the twig. Having descended a little by twisting the wire along the main trunk, we can begin to add further branches. At the same time, when we make a twist along the main trunk of a branch, we display a long edge of the wire on the right. And it is on the right that each time we will collect a new branch, leaving the previous branch on the left.

Our next branch will consist of one bead of freshwater pearls. We string it again on a long piece of wire and move it to the rest of the elements. We measure the desired length of the leg and start twisting to the main trunk. After that, we make several twists around the main trunk of the branch.

We add the next three branches in the same way as we added a branch with a bead of freshwater pearls. For this, we first use a glass bead bicone, then a transparent bead and a matte one.

I want to draw your attention to the fact that with each branch it is necessary to make its leg a little longer than that of the previous branch. If we make them all the same length, then the branch will turn out to be quite small and not voluminous.

Next, I propose to make an element in the form of a leaflet. We collect 7 beads on the long edge of the wire. We find the penultimate bead, which was typed on the wire and through it again we pass the wire in the opposite direction and tighten it. It turns out our last bead and will fix the edge of the leaf. After we have fixed the bead, we collect five more beads on the free edge of the wire. We get a pattern in the form of a leaf. With one hand we hold the beads so that they do not run away, and with the other hand we begin to twist them carefully.

This leaf has a rather long stem. Therefore, you can make a branch from it and add another element. To do this, I will take a twin bead, run it through the wire through only one hole and make a small branch out of it. This branch connected with a branch of a petal of beads. Next, we twist them to the base of the common branch, and then scroll the common base itself several times.

Now we will make another branch, which will consist of three small branches, at the end of which, we will use beads in the form of bicones. First we string one bicone. Next, measuring the desired length of the leg, we do several twists. About half of our legs. We string the second bicone on the wire. We measure the desired length of the legs and also twist. Then we make several turns of general twisting already with two bicones. Now you can string the third bicone. We tried on the leg and twist along this branch, and then to the main column of the branch.

Now we will show how to make elements with large beads for our jewelry. We add a few more branches to the right and left sides of the general column of the branch, using for this different amount beads and branches. We will also collect one branch using a decorative element in the form of a leaf. And add the next branch with a bead and decorate it with bead caps. We have a long branch ready.

Now let's move on to the short branch that will be on our side. To do this, take the long end of the wire. Approximately we measure the length of our future branch and stringing the fittings in the desired order one by one, we collect the branch and twist it.

Next, we need to fix the branch on the hairpin. We take the short end of the wire and through the nearest branches we make several turns around the hairpin. We stretch our wire tightly so that our product does not hang out on the hairpin in the future and sits tightly. When fixing, you can add a few more decorative elements or twigs. To do this, use the long end of the wire. The winding around the hairpin can be hidden using any large bead, securing it with a wire at the very base of the hairpin. We twist the remaining ends of the wire around the hairpin and remove the excess with wire cutters. We press the edges of the wires with pliers so that they do not prick or hide the ends of the wires in the nearest beads.

Hair ornament is ready! You can make such decorations for hairstyles with your own hands from a wide variety of fittings, as well as various shapes, colors and sizes of beads.

Everything necessary materials, which I used in this master class, you will find in our online jewelry accessories store. For a more detailed explanation of the assembly of this jewelry, you can watch our video tutorial:

Wire pendants with stones

Wire is a strong and malleable material that can take any shape. The unique properties of thin metal threads were successfully used by ancient jewelers, who weaved filigree patterns, creating jewelry of amazing beauty. The material holds its shape well, has a noble luster, isn't it a paradise for the modern jewelry industry? Modern craftsmen can, as if by magic, turn a coil of ordinary wire into spectacular and stylish accessories. Do you want to learn how to make exclusive wire jewelry with your own hands? Then we offer to master the simple ABC of craftsmanship, and learn how to create real miracles using the example of master classes.

Basics for beginners

The names of the ancient jewelers who successfully embodied the fantasy in wire jewelry are unknown to contemporaries. type of art wire wrap”, which means “wire wrapping”, went down in history under the name of craftsman Alexander Calder. Master with early years learned to weave original products. He made the first crafts as a gift to relatives and friends, and later an unusual hobby turned into a lifelong business. Original, original, openwork works inspired many to accomplish creative feats.

Alexander Calder and his work

The main principle of such needlework is to use thick wire for the base and thinner and more flexible for braiding products.

Wire wrap pendant

In weaving, you can add beads, stones, all kinds of decor. By the way, if the wire is braided on top with a thin thread, then such needlework is called ganutel. To learn how to create beautiful wire accessories, you need to know a few simple secrets:

Selection of tools. The job requires a small arsenal of tools. Beginners will need round nose pliers, several types of pliers with sharp, nylon, rectangular tips, a wick or sandpaper. To create complex weaves of patterns, experienced craftsmen use anvils, a spur and a hammer, crossbars and a drawing board in their work.
So that, in the end, home-made jewelry made of wire has, as they say, a “shop gloss”, you can use sulfuric liver to cover it. With this material, products made of copper, aluminum, brass, bronze wire are patinated to create a noble effect of antiquity.
It is enough to master the creation of several elements to make an author's masterpiece. The simplest elements include a spring, balls and rings.

Wire Tools

To make a spring, it is enough to wind a piece of wire around the crossbar. Such an element can be used for braiding or as an independent decorative detail. To make a ball, you will need a burner or gas burner. To make the droplets perfectly even, you need a drill. By the way, you can create new interesting elements from a ball with a hammer and anvil. Rings are connecting parts, indispensable in the creation of beads or bracelets. It is enough to wind the wire on the crossbar, “bite off” the excess and remove the perfectly even ring. The diameter of the ring depends on the thickness of the crossbar. Having obtained the necessary knowledge, having prepared necessary tools and materials, you can begin the creative process.

Use of improvised tools for working with wire

Master classes on creating jewelry

Unusual jewelry made of copper wire, bronze or brass, can acquire the most different forms. For example, you can make original jewelry for hair, rings and bracelets, openwork necklaces or pendants. Beginners should not worry about the lack of practice and experience in creative work, simple and detailed wizard the class will help in creating the author's collection of luxurious jewelry.

Turquoise copper wire earrings

Hair ornaments

In anticipation proms such a master class is especially relevant, because many girls are in creative search for your image. I want to be the brightest, most beautiful, exclusive. There is the right way create an unusual look by decorating stylish hairstyle hairpin hand made in the form of a flower with an elegant curl. The algorithm of work is the following:

On a piece of paper we will draw a sketch of the future product, schematically noting the location of the beads and the pattern on it.
We start work with a coil, smoothly moving to the outer circle of the product. Place the end in a spiral that is slightly higher. The result should be a round element with antennae. We work continuously with round-nose pliers to make the product neat.
We twist the place where two curls touched with a few more tight turns, weave in the beads, and then braid the base of the hairpin with a thin wire.

Stylish decoration for hair

To make it clearer for beginner craftswomen, we offer an auxiliary scheme:

six curls between beads;
ten curls between large elements;
eight curls between smaller elements.

simple hairstyle with spectacular decoration

To make the hairpin gentle and have a finished look, we string small beads at the beginning of weaving, and large beads can be woven into the middle.

Similarly, you can make not only a hairpin. There is original way decorate hairpins - just braid with a thin metal thread, adding a few beads or beads to the weave.

Delicate hair ornaments based on hairpins

Luxurious pendant

Copper wire has high ductility, it can be easily cut, heated, soldered. Thanks to their unique properties, budget and beautiful in appearance, the material has become a favorite in needlework. What can be done from copper wire with your own hands? Yes, everything that fantasy tells you - bracelets, rings, pendants and much more. Luxurious wire pendant master class:

Prepare tools and materials. You will need a coil of copper wire with a cross section of 0.1 mm to 1 mm, pearl beads, wire cutters, round pliers and a drill.
The main part of the product consists of two segments of 16 cm long and 1 mm thick. We make turns with a thin copper thread 0.1 mm around thicker segments, then bend the two braided parts into a ring. We bend the remaining tips with a snail.
We wind a thin one on a segment with a thickness of 0.3 mm, the length of the base is 12 cm. We pass its end between the wicker parts, fix it. We make a small kink, wrap it around the frame several times.
In the upper part we make the same kink, and the remaining part is wound on the base. We make a snail from a wire 1 mm thick, we wind it to one and the other kink.
A thin wire thread is attached to the upper part, pearls are strung on it, the ends of the wires braid the workpiece, and we bite off the excess with wire cutters. So add all the prepared beads.

Copper wire pendant with pearls

In order for the product to have an elegant glossy sheen, we polish the surface of the pendant with a drill, and then rinse it under warm water. Luxurious, intricate, in the spirit of oriental jewelry of the Magnificent Age, the pendant is ready to decorate any lady's outfit.

sweet heart

There are many workshops on making stylish wire jewelry, on the example of which you can learn how to create magnificent author's collections. But a few simple tips will help beginners to do the job at a decent level:

In order not to patinate the wire, non-oxidizing materials should be used. For durability, you can varnish the surface.
After heating the wire on the fire, rub it with baby cream while still warm, and then wash it off with soap and water. Patina - the effect, as they say, on the fan. Many craftsmen prefer to cover the jewelry with gold, silver or bronze paint, and varnish it on top for shine.
Be sure to draw a diagram and sketch of jewelry before starting work. Working with wire is thin and filigree, it requires attention and perseverance. When you see a wire decoration that you want to repeat with your own hands, mentally divide it into components, so it will be easier to work.

Each master has his own fantasy, creative ideas and a vision of a future masterpiece. All kinds of decor, such as beads, beads, stones and even buttons, are ideally combined with wire. For beginners, you can use ready-made master classes for practice, and in the process of weaving, supplement the idea with your own details.